Fiber-Type Transistor-Based Chemical and Physical Sensors Using Conjugated Polymers.

Fiber-type electronics is a crucial field for realizing wearable electronic devices with a wide range of sensing applications. In this paper, we begin by discussing the fabrication of fibers from conjugated polymers. We then explore the utilization of these fibers in the development of field-effect and electrochemical transistors. Finally, we investigate the diverse applications of these fiber-type transistors, encompassing chemical and physical sensors. Our paper aims to offer a comprehensive understanding of the use of conjugated polymers in fiber-type transistor-based sensors.

Optimization of Gas-Sensing Properties in Poly(triarylamine) Field-Effect Transistors by Device and Interface Engineering.

In this study, we investigated the gas-sensing mechanism in bottom-gate organic field-effect transistors (OFETs) using poly(triarylamine) (PTAA). A comparison of different device architectures revealed that the top-contact structure exhibited superior gas-sensing performance in terms of field-effect mobility and sensitivity. The thickness of the active layer played a critical role in enhancing these parameters in the top-contact structure. Moreover, the distance and pathway for charge carriers to reach the active channel were found to significantly influence the gas response. Additionally, the surface treatment of the SiO2 dielectric with hydrophobic self-assembled mono-layers led to further improvement in the performance of the OFETs and gas sensors by effectively passivating the silanol groups. Under optimal conditions, our PTAA-based gas sensors achieved an exceptionally high response (>200%/ppm) towards NO2. These findings highlight the importance of device and interface engineering for optimizing gas-sensing properties in amorphous polymer semiconductors, offering valuable insights for the design of advanced gas sensors.

Side-Chain-Assisted Transition of Conjugated Polymers from a Semiconductor to Conductor and Comparison of Their NO2 Sensing Characteristics.

To investigate the effect of a side chain on the electrical properties of a conjugated polymer (CP), we designed two different CPs containing alkyl and ethylene glycol (EG) derivatives as side chains on the same conjugated backbone with an electron donor-acceptor (D-A) type chain configuration. PTQ-T with an alkyl side chain showed typical p-type semiconducting properties, whereas PTQ-TEG with an EG-based side chain exhibited electrically conductive behavior. Both CPs generated radical species owing to their strong D-A type conjugated structure; however, the spin density was much greater in PTQ-TEG. X-ray photoelectron spectroscopy analysis revealed that the O atoms of the EG-based side chains in PTQ-TEG were intercalated with the conjugated backbone and increased the carrier density. Upon application to a field-effect transistor sensor for PTQ-T and resistive sensor for PTQ-TEG, PTQ-TEG exhibited a better NO2 detection capability with faster signal recovery characteristics than PTQ-T. Compared with the relatively rigid alkyl side chains of PTQ-T, the flexible EG-based side chains in PTQ-TEG have a higher potential to enlarge the free volume as well as improve NO2-affinity, which promotes the diffusion of NO2 in and out of the PTQ-TEG film, and ultimately resulting in better NO2 detection capabilities.

Microstructural Control of Soluble Acene Crystals for Field-Effect Transistor Gas Sensors.

Microstructural control during the solution processing of small-molecule semiconductors (namely, soluble acene) is important for enhancing the performance of field-effect transistors (FET) and sensors. This focused review introduces strategies to enhance the gas-sensing properties (sensitivity, recovery, selectivity, and stability) of soluble acene FET sensors by considering their sensing mechanism. Defects, such as grain boundaries and crystal edges, provide diffusion pathways for target gas molecules to reach the semiconductor-dielectric interface, thereby enhancing sensitivity and recovery. Representative studies on grain boundary engineering, patterning, and pore generation in the formation of soluble acene crystals are reviewed. The phase separation and microstructure of soluble acene/polymer blends for enhancing gas-sensing performance are also reviewed. Finally, flexible gas sensors using soluble acenes and soluble acene/polymer blends are introduced, and future research perspectives in this field are suggested.

Ultrasensitive N-Channel Graphene Gas Sensors by Nondestructive Molecular Doping.

Sensitive and selective detection of target gases is the ultimate goal for commercialization of graphene gas sensors. Here, ultrasensitive n-channel graphene gas sensors were developed by using n-doped graphene with ethylene amines. The exposure of the n-doped graphene to oxidizing gases such as NO2 leads to a current decrease that depends strongly on the number of amine functional groups in various types of ethylene amines. Graphene doped with diethylenetriamine (DETA) exhibits the highest response, recovery, and long-term sensing stability to NO2, with an average detection limit of 0.83 parts per quadrillion (ppq, 10-15), due to the attractive electrostatic interaction between electron-rich graphene and electron-deficient NO2. Our first-principles calculation supported a preferential adsorption of NO2 on n-doped graphene. In addition, gas molecules on the n-channel graphene provide charged impurities, thereby intensifying the current decrease for an excellent response to oxidizing gases such as NO2 or SO2. On the contrary, absence of such a strong interaction between NH3 and DETA-doped graphene and combined effects of current increase by n-doping and mobility decrease by charged impurities result in a completely no response to NH3. Because the n-channel is easily induced by a top-molecular dopant, a flexible graphene sensor with outstanding NO2 detection capability was successfully fabricated on plastic without vertical stacks of gate-electrode and gate-dielectric. Our gate-free graphene gas sensors enabled by nondestructive molecular n-doping could be used for the selective detection of subppq-level NO2 in a gas mixture with reducing gases.

NO2-Affinitive Conjugated Polymer for Selective Sub-Parts-Per-Billion NO2 Detection in a Field-Effect Transistor Sensor.

Conjugated polymers (CPs) have provided versatile semiconducting implements for the development of soft electronic devices. When three CPs with the same conjugated framework but different side chains were adopted in the field-effect transistor (FET) sensor for NO2 detection, the response to NO2 showed an opposite tendency to the charge carrier mobility of each CP. Morphological and structural characterizations revealed that the flexible glycol side chain enhances NO2 affinity as well as prevents the formation of lamellar stacking of the CP chains, thereby providing routes for the facile diffusion of NO2. Additionally, theoretical calculations for CP-NO2 complex formation at the molecular level support the relatively low energy barrier for inter-chain transition of NO2 between the glycol-based conjugated frameworks, which implies the spontaneous internal diffusion of NO2 to the semiconductor-dielectric interface in the FET-based sensor. As a result, the CP with a NO2-affinitive morphology exhibited an exceptional sensitivity of 13.8%/ppb upon NO2 (100 ppb) exposure for 50 s and provided excellent selectivity to the FET-based sensor toward other environmentally abundant harmful gases, such as SO2, CO2, and NH3. In particular, the theoretic limit of detection reached down to 0.24 ppb, which is the lowest value ever reported for organic FET-based NO2 gas sensors.

Enhanced Gas Sensing Properties of Graphene Transistor by Reduced Doping with Hydrophobic Polymer Brush as a Surface Modification Layer.

Surface modification layer of a silicon substrate has been used to enhance the performance of graphene field-effect transistors (FETs). In this report, ultrathin and chemically robust polymer brush was used as a surface modification to enhance the gas sensing properties of graphene FETs. The insertion of the polymer brush decreased substrate-induced doping of graphene. This leads to a huge increase in field-effect mobility as well as a minimum shift of the Dirac point voltage. The use of the polymer brush enables fast detection of target gas molecules because graphene sensing modality can be maximized at the undoped state of graphene. The increase of source-drain current, as well as the abrupt decrease of electron mobility upon NO2 exposure, was utilized for the instantaneous detection, and a limit of detection of 4.8 ppb was achieved with graphene FETs on PS brush. We also showed excellent cross-sensitivity of graphene gas sensors to NH3, CO2, and relative humidity condition; the source-drain current decreases upon NH3 exposure, while response to CO2 or relative humidity condition is extremely low. Our results prove that reducing the substrate-induced doping of graphene with a polymer brush is a direct method for boosting the gas sensing properties of graphene FETs.

Tailoring the crystallinity of solution-processed 6,13-bis(triisopropylsilylethynyl)pentacene via controlled solidification.

Solution processing is one of the most important techniques for producing large-area, uniform films for printed electronics via a low-cost process. Herein, we propose a time-controlled spin-coating method to improve the crystallinity of films of the solution-processable organic small-molecule semiconductor 6,13-bis(triisopropylsilylethynyl)pentacene (TIPS-pentacene). A key factor in this process was to halt spinning before drying had begun. We used microscopic and spectroscopic analyses to systematically investigate the effect of spinning time on the evaporation rate of solvent at different spinning rates. We found that the crystallinity of the TIPS-pentacene thin films was substantially enhanced when the spinning time was limited to a few seconds, without post-treatment. We fabricated field-effect transistors using thin films deposited by this method and found that the field-effect mobility was enhanced ∼100-fold compared with that of a device fabricated using a film deposited by the conventional spin-coating method.

Attomolar detection of virus by liquid coplanar-gate graphene transistor on plastic.

The direct method of detecting a virus with extremely low concentration is recommended for the diagnosis of viral disease. In this study, coplanar-gate graphene field-effect transistors (GFETs) were built on flexible polyethylene terephthalate substrates for the attomolar detection of a virus. The GFETs exhibited a very low detection limit of 47.8 aM with relatively low source/drain voltage due to aqueous dielectric media which stabilizes viruses and antibodies for specific bonding. The antibody as a probe molecule was decorated on a graphene surface using 1-pyrenebutanoic acid succinimidyl ester that had previously been immobilized on a graphene surface. The Dirac point voltage shifted downward after dropping the virus solution, due to the electrostatic gating effect of graphene in the antigen (namely, virus)-antibody complex. The virus detection platform used in this study is expected to be beneficial for direct diagnosis in saline environments, since the performances of GFETs were not significantly affected by the presence of Na+ and Cl-. Furthermore, since our flexible and transparent virus sensors can be used in a wearable device, they provide a simple and fast method for diagnosing viruses.

Effect of Crystallization Modes in TIPS-pentacene/Insulating Polymer Blends on the Gas Sensing Properties of Organic Field-Effect Transistors.

Blending organic semiconductors with insulating polymers has been known to be an effective way to overcome the disadvantages of single-component organic semiconductors for high-performance organic field-effect transistors (OFETs). We show that when a solution processable organic semiconductor (6,13-bis(triisopropylsilylethynyl)pentacene, TIPS-pentacene) is blended with an insulating polymer (PS), morphological and structural characteristics of the blend films could be significantly influenced by the processing conditions like the spin coating time. Although vertical phase-separated structures (TIPS-pentacene-top/PS-bottom) were formed on the substrate regardless of the spin coating time, the spin time governed the growth mode of the TIPS-pentacene molecules that phase-separated and crystallized on the insulating polymer. Excess residual solvent in samples spun for a short duration induces a convective flow in the drying droplet, thereby leading to one-dimensional (1D) growth mode of TIPS-pentacene crystals. In contrast, after an appropriate spin-coating time, an optimum amount of the residual solvent in the film led to two-dimensional (2D) growth mode of TIPS-pentacene crystals. The 2D spherulites of TIPS-pentacene are extremely advantageous for improving the field-effect mobility of FETs compared to needle-like 1D structures, because of the high surface coverage of crystals with a unique continuous film structure. In addition, the porous structure observed in the 2D crystalline film allows gas molecules to easily penetrate into the channel region, thereby improving the gas sensing properties.

Manipulation of Chain Conformation for Optimum Charge-Transport Pathways in Conjugated Polymers.

A pair of different diketopyrrolopyrrole-based conjugated polymers (CPs) were designed and synthesized to investigate the effect of chain conformation on their molecular assembly. Conformation management was achieved by the incorporation of different linkers during polymerization. Through the use of computational calculations and UV-vis absorption measurements, the resulting CPs (PDPP-T and PDPP-BT) were found to exhibit partly modulated chain geometry. Grazing incident X-ray diffraction experiments with a two-dimensional detector revealed that PDPP-T having a planar chain conformation exhibited an edge-on type molecular arrangement, which evolved to a face-on type chain assembly when the planar geometry was altered to a slightly twisted one as in PDPP-BT. In addition, it was verified that the directional electric carrier mobility of CPs was critically distinguished by the distinctive chain arrangement in spite of their similar chemical structure. Concentration-dependent absorption measurements could provide an improved understanding of the assembly mechanism of CP chains: the planar conformation of PDPP-T facilitates the formation of preassembled chains in a concentrated solution and further directs the edge-on stacking, while the twisted dihedral angle along the benzothiophene in PDPP-BT prevents chain assembly, resulting in the face-on stacking. Because CP chain conformation is inevitably connected with the generation of preassembled chains, manipulating CP geometry could be an efficient tool for extracting an optimum chain assembly that is connected with the principal charge-transport pathway in CPs.

Gate- and Light-Tunable pn Heterojunction Microwire Arrays Fabricated via Evaporative Assembly.

One-dimensional (1D) nano/microwires have attracted considerable attention as versatile building blocks for use in diverse electronic, optoelectronic, and magnetic device applications. The large-area assembly of nano/microwires at desired positions presents a significant challenge for developing high-density electronic devices. Here, we demonstrated the fabrication of cross-stacked pn heterojunction diode arrays by integrating well-aligned inorganic and organic microwires fabricated via evaporative assembly. We utilized solution-processed n-type inorganic indium-gallium-zinc-oxide (IGZO) microwires and p-type organic 6,13-bis(triisopropylsilylethynyl)pentacene (TIPS-PEN) microwires. The formation of organic TIPS-PEN semiconductor microwire and their electrical properties were optimized by controlling both the amounts of added insulating polymer and the widths of the microwires. The resulting cross-stacked IGZO/TIPS-PEN microwire pn heterojunction devices exhibited rectifying behavior with a forward-to-reverse bias current ratio exceeding 102. The ultrathin nature of the underlying n-type IGZO microwires yielded gate tunability in the charge transport behaviors, ranging from insulating to rectifying. The rectifying behaviors of the heterojunction devices could be modulated by controlling the optical power of the irradiated light. The fabrication of semiconducting microwires through evaporative assembly provides a facile and reliable approach to patterning or positioning 1D microwires for the fabrication of future flexible large-area electronics.

Inkjet Etching of Polymers and Its Applications in Organic Electronic Devices.

Inkjet printing techniques for the etching of polymers and their application to the fabrication of organic electronic devices are reviewed. A mechanism is proposed for the formation of via holes in polymer layers through inkjet printing with solvent, and recent achievements in the fabrication with inkjet etching of various three-dimensional microstructures (i.e., microwells, microgrooves, hexagonal holes, and concave structures) are discussed. In addition, organic electronic devices are presented that use inkjet-etched subtractive patterns as platforms for the selective depositions of an emissive material, a liquid crystal, an organic conductor, an organic insulator, and an organic semiconductor, and as an optical waveguide.

Grain Boundary Induced Bias Instability in Soluble Acene-Based Thin-Film Transistors.

Since the grain boundaries (GBs) within the semiconductor layer of organic field-effect transistors (OFETs) have a strong influence on device performance, a substantial number of studies have been devoted to controlling the crystallization characteristics of organic semiconductors. We studied the intrinsic effects of GBs within 5,11-bis(triethylsilylethynyl) anthradithiophene (TES-ADT) thin films on the electrical properties of OFETs. The GB density was easily changed by controlling nulceation event in TES-ADT thin films. When the mixing time was increased, the number of aggregates in as-spun TES-ADT thin films were increased and subsequent exposure of the films to 1,2-dichloroethane vapor led to a significant increase in the number of nuleation sites, thereby increasing the GB density of TES-ADT spherulites. The density of GBs strongly influences the angular spread and crystallographic orientation of TES-ADT spherulites. Accordingly, the FETs with higher GB densities showed much poorer electrical characteristics than devices with lower GB density. Especially, GBs provide charge trapping sites which are responsible for bias-stress driven electrical instability. Dielectric surface treatment with a polystyrene brush layer clarified the GB-induced charge trapping by reducing charge trapping at the semiconductor-dielectric interface. Our study provides an understanding on GB induced bias instability for the development of high performance OFETs.

Facet-Mediated Growth of High-Quality Monolayer Graphene on Arbitrarily Rough Copper Surfaces.

A synthetic approach for high-quality graphene on rough Cu surfaces via chemical vapor deposition is proposed. High-quality graphene is synthesized on rough Cu surfaces by inducing surface faceting of Cu surfaces prior to graphene growth. The electron mobility of synthesized graphene on the rough Cu surfaces is enhanced to 10 335 cm(2) V(-1) s(-1).

Inkjet-Printed Organic Transistors Based on Organic Semiconductor/Insulating Polymer Blends.

Recent advances in inkjet-printed organic field-effect transistors (OFETs) based on organic semiconductor/insulating polymer blends are reviewed in this article. Organic semiconductor/insulating polymer blends are attractive ink candidates for enhancing the jetting properties, inducing uniform film morphologies, and/or controlling crystallization behaviors of organic semiconductors. Representative studies using soluble acene/insulating polymer blends as an inkjet-printed active layer in OFETs are introduced with special attention paid to the phase separation characteristics of such blended films. In addition, inkjet-printed semiconducting/insulating polymer blends for fabricating high performance printed OFETs are reviewed.

Engineering Optical and Electronic Properties of WS2 by Varying the Number of Layers.

The optical constants, bandgaps, and band alignments of mono-, bi-, and trilayer WS2 were experimentally measured, and an extraordinarily high dependency on the number of layers was revealed. The refractive indices and extinction coefficients were extracted from the optical-contrast oscillation for various thicknesses of SiO2 on a Si substrate. The bandgaps of the few-layer WS2 were both optically and electrically measured, indicating high exciton-binding energies. The Schottky-barrier heights (SBHs) with Au/Cr contact were also extracted, depending on the number of layers (1-28). From an engineering viewpoint, the bandgap can be modulated from 3.49 to 2.71 eV with additional layers. The SBH can also be reduced from 0.37 eV for a monolayer to 0.17 eV for 28 layers. The technique of engineering materials' properties by modulating the number of layers opens pathways uniquely adaptable to transition-metal dichalcogenides.

Boosting Photon Harvesting in Organic Solar Cells with Highly Oriented Molecular Crystals via Graphene-Organic Heterointerface.

Photon harvesting in organic solar cells is highly dependent on the anisotropic nature of the optoelectronic properties of photoactive materials. Here, we demonstrate an efficient approach to dramatically enhance photon harvesting in planar heterojunction solar cells by using a graphene-organic heterointerface. A large area, residue-free monolayer graphene is inserted at anode interface to serve as an atomically thin epitaxial template for growing highly orientated pentacene crystals with lying-down orientation. This anisotropic orientation enhances the overall optoelectronic properties, including light absorption, charge carrier lifetime, interfacial energetics, and especially the exciton diffusion length. Spectroscopic and crystallographic analysis reveal that the lying-down orientation persists until a thickness of 110 nm, which, along with increased exciton diffusion length up to nearly 100 nm, allows the device optimum thickness to be doubled to yield significantly enhanced light absorption within the photoactive layers. The resultant photovoltaic performance shows simultaneous increment in Voc, Jsc, and FF, and consequently a 5 times increment in the maximum power conversion efficiency than the equivalent devices without a graphene layer. The present findings indicate that controlling organic-graphene heterointerface could provide a design strategy of organic solar cell architecture for boosting photon harvesting.

Clean Transfer of Wafer-Scale Graphene via Liquid Phase Removal of Polycyclic Aromatic Hydrocarbons.

Pentacene (C22H14), a polycyclic aromatic hydrocarbon, was used as both supporting and sacrificing layers for the clean and doping-free graphene transfer. After successful transfer of graphene to a target substrate, the pentacene layer was physically removed from the graphene surface by using intercalating organic solvent. This solvent-mediated removal of pentacene from graphene surface was investigated by both theoretical calculation and experimental studies with various solvents. The uses of pentacene and appropriate intercalation solvent enabled graphene transfer without forming a residue from the supporting layer. Such residues tend to cause charged impurity scattering and unintentional graphene doping effects. As a result, this clean graphene exhibited extremely homogeneous surface potential profiles over a large area. A field-effect transistor fabricated using this graphene displayed a high hole (electron) mobility of 8050 cm(2)/V·s (9940 cm(2)/V·s) with a nearly zero Dirac point voltage.

Chemically tunable ultrathin silsesquiazane interlayer for n-type and p-type organic transistors on flexible plastic.

In organic field-effect transistors (OFETs), surface modification of the gate-dielectric is a critical technique for enhancing the electrical properties of the device. Here, we report a simple and versatile method for fabricating an ultrathin cross-linked interlayer (thickness ∼3 nm) on an oxide gate dielectric by using polymeric silsesquiazane (SSQZ). The fabricated siloxane film exhibited an ultrasmooth surface with minimal hydroxyl groups; the properties of the surface were chemically tuned by introducing phenyl and phenyl/fluorine pendent groups into the SSQZ. The growth characteristics of two semiconductors-pentacene (p-type) and N,N'-ditridecyl-3,4,9,10-perylene tetracarboxylic diimide (PTCDI-C13, n-type)-on this ultrathin film were systematically investigated according to the type of pendent groups in the SSQZ-treated gate dielectric. Pentacene films on phenyl/fluorine groups exhibited large grains and excellent crystalline homogeneity. By contrast, PTCDI-C13 films exhibited greater crystalline order and perfectness when deposited on phenyl groups rather than on phenyl/fluorine groups. These microstructural characteristics of the organic semiconductors, as well as the dipole moment of the pendent groups, determined the electrical properties of FETs based on pentacene or PTCDI-C13. Importantly, compared to FETs in which the gate dielectric was treated with a silane-coupling agent (a commonly used surface treatment), the FETs fabricated using the tunable SSQZ treatment showed much higher field-effect mobilities. Finally, surface treatment with an ultrathin SSQZ layer was also utilized to fabricate flexible OFETs on a plastic substrate. This was facilitated by the facile SSQZ deposition process and the compatibility of SSQZ with the plastic substrate.